Author Topic: Rat Gat (Read 54863 times)

Cutter · « **Reply #280 on:** April 25, 2016, 03:21:50 PM »

I can\'t load a MP4 / gopro video.

Cutter · « **Reply #281 on:** April 25, 2016, 05:44:57 PM »

I zipped two videos, hope this works

Cutter · « **Reply #282 on:** April 25, 2016, 06:49:47 PM »

Hereâ€™s another zip file.

The video from the drone is over 1 gig , my buddy

needs to do some editing

Cutter · « **Reply #283 on:** April 30, 2016, 10:39:33 AM »

Shorty has the magazine adapter mounted with a limited opening hinge and two
new Sticks of 30 rounds each. Sticks have a manual open / close switch.
Testing soon.

Cutter · « **Reply #284 on:** May 01, 2016, 10:34:29 AM »

Hereâ€™s a short video from the drone.

He needs to zoom in

Maybe we can do better next time.

The Drone strikes back

Cutter · « **Reply #285 on:** May 01, 2016, 10:43:13 AM »

Seems to work ok without the weight

Cutter · « **Reply #286 on:** July 12, 2016, 11:18:55 AM »

Some testing with the new stick magazines.

This 6â€™5â€ Marine makes the gat look pretty small

Dave · « **Reply #287 on:** July 12, 2016, 06:26:05 PM »

Those videos are pretty amazing!

The drone vid is cool too :mrgreen:

Cutter · « **Reply #288 on:** July 19, 2016, 12:22:54 PM »

Maybe a chain drive this time

Cutter · « **Reply #289 on:** July 31, 2016, 06:03:22 PM »

I just finished the main shafts for the new builds
Yep two this time, The other main shaft is laying in front.
Another set of barrels is on the way.
I already have the gears, so gear drive for both.

Cutter · « **Reply #290 on:** September 17, 2016, 03:22:26 PM »

Barrels mounted , I think the Receivers are next.

joboxxer · « **Reply #291 on:** September 21, 2016, 10:54:07 AM »

Looking good again Jerry. The show-me state license plate seems a little far from home.

Cutter · « **Reply #292 on:** September 21, 2016, 12:12:41 PM »

Hey joboxxer,

I was on the run from my first wife and her lawyers in the early 80s

The Ozarks, a great place to hide. They never found me.

Number two went to Nevada, that was an easy one.

Cutter · « **Reply #293 on:** September 25, 2016, 12:46:37 PM »

The front crossover piece of frame with ball bearing
pressed inside and thrust bearing in front.
The recoil plate will also have a ball bearing pressed in.

Cutter · « **Reply #294 on:** September 27, 2016, 06:12:43 PM »

Finished cutting the rails today, mounted front piece
and cut the inside radius for the casing.
casing/receiver material not here yet .

Cutter · « **Reply #295 on:** September 29, 2016, 05:08:53 PM »

I have the casings mounted in the frame and crank shaft in place.
I need a couple days to tidy up, I got shit everywhere.

Cutter · « **Reply #296 on:** October 04, 2016, 01:45:42 PM »

Gears are keyed in place.

Next some crank handles and end caps with thrust washers

4171 · « **Reply #297 on:** October 06, 2016, 03:02:29 PM »

Damn Cutter your a gatling gun making machine :mrgreen: I really like the \"new\" style frame!

Mike

Cutter · « **Reply #298 on:** October 06, 2016, 07:50:49 PM »

These are very simple Mike, no bells or whistles.

Just shooters

Cutter · « **Reply #299 on:** October 07, 2016, 04:04:20 PM »

Cranks are finished

News:

Author Topic: Rat Gat (Read 54863 times)