Jump to content


Photo

Ruger style extractors


  • Please log in to reply
8 replies to this topic

#1 gbull

gbull

    Advanced Member

  • Members
  • PipPipPip
  • 52 posts
  • LocationGold Bar Wa.

Posted 04 June 2020 - 06:28 AM

I have 80 extractors, EDM wire cut from prehardened steel using Cutters dxf. They are ready to use. They come as a package with the spring and plunger. Also included is a firing pin spring. The price is $12 each. Shipping is $5. A set of ten comes to $149. They also come with a drawing another member has made for locations of holes and mill cuts. This is a reliable alternative to the original RG-G design. Very simple and easier to assemble. The springs are from Lee Springs, and are individually priced much lower than the low qty. price. If there is enough interest I may do another run of at least 100. Thanks for looking.

Attached Files


  • bruski and Cutter like this

#2 butch

butch

    Newbie

  • Members
  • Pip
  • 0 posts
  • LocationWheat Ridge CO

Posted 04 June 2020 - 12:36 PM

Message sent, thanks



#3 gbull

gbull

    Advanced Member

  • Members
  • PipPipPip
  • 52 posts
  • LocationGold Bar Wa.

Posted 04 June 2020 - 08:40 PM

The price total should be $125 for 10 sets. I should know better than posting late at night.

#4 brk

brk

    Advanced Member

  • Members
  • PipPipPip
  • 31 posts
  • LocationSouthern Illinois

Posted 04 June 2020 - 08:50 PM

I will take a set, I have sent a message



#5 rayhawk

rayhawk

    Member

  • Members
  • PipPip
  • 10 posts

Posted 04 June 2020 - 10:49 PM

Gary, if it is my drawing, you are certainly free to share it but I have been working on some updates based on the actual geometry of your extractors and the key cutter I just got today. I would like to run some parts from it before we "release" the drawing to the community.


  • gbull likes this

#6 20Gun

20Gun

    Member

  • Members
  • PipPip
  • 13 posts
  • LocationShow Me State

Posted 05 June 2020 - 10:50 AM

I'll take a set. PM sent.



#7 DonV

DonV

    Member

  • Members
  • PipPip
  • 11 posts

Posted 12 June 2020 - 04:15 PM

Any way to retool bolts already machined for RG&G extractors?

Don

#8 Cutter

Cutter

    Advanced Member

  • Members
  • PipPipPip
  • 1158 posts

Posted 12 June 2020 - 06:22 PM

Any way to retool bolts already machined for RG&G extractors?

Don

 

Hi Don,
I would removed the recoil pin and cut the front
of the bolt off just at the rear of the RG-G
extractor slot and press a new piece in
and pin it.


#9 Cutter

Cutter

    Advanced Member

  • Members
  • PipPipPip
  • 1158 posts

Posted 13 June 2020 - 04:34 PM

DonV
 
This bolt worked very well just was not
popular with members on the RG-G forum
( about 2003 )
The sections are threaded and locked together.
It all works the same inside 
These bolts used 1/32 spring steel extractors
similar to the picture

Attached Files


  • bruski and Swarfmonger like this




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users